Portable PD Tester for Transformer Factory and FAT/SAT | MOEORW
Product Introduction
The multifunctional partial discharge detector (widely recognized as the All-in-One PD Tester for Factory QA) is an advanced handheld live-line partial discharge detector engineered for high-voltage equipment inspection. Designated as the MOEORW‑Wi900PD, this multi-channel partial discharge monitoring system integrates TEV, UHF, HFCT, AA, and AE sensors to deliver AI-powered defect diagnosis and professional PRPD & PRPS pattern analysis for power utilities worldwide.
Serving as a highly cost-effective portable pd tester alternative to mpd system, the MOEORW‑Wi900PD is the definitive portable pd tester for transformer factory quality control, fully optimizing both portable pd tester for transformer fat and sat (Factory/Site Acceptance Testing) protocols. Engineered for field efficiency, this instrument enables sensitive portable offline pd tester evaluations and seamless portable pd testing without complex setup, making it the ultimate tool for ongoing electrical equipment diagnostics and comprehensive power grid maintenance
Technical Parameters
| Item | Specification |
|---|---|
| Detection Channel | TEV, UHF, HFCT, AA, AE |
| Analysis Function | PRPD, PRPS, AI defect identification |
| Working Mode | Non‑intrusive live‑line testing |
| Battery | 5000mAh, ≥8h continuous working |
| Protection Grade | IP66‑IP68 |
| Working Temp | ‑40℃ ~ +85℃ |
Please see below for full specifications
Product Features
Multi‑sensor Fusion Detection: TEV, UHF, HFCT, AA, AE
Built‑in TEV and AA sensors on main unit, with external interfaces for UHF, HFCT, AE and focused flexible AA probe. Multi‑mode detection avoids missed defects caused by single‑sensor testing, complying with IEC 60270 standard for partial discharge measurement.
One partial discharge tester covers full‑scene inspection for switchgear, GIS, transformer and HV cable, reducing extra instrument investment for your projects.
Learn more about partial discharge detection methods
AI-Driven Automation in Electrical Equipment Diagnostics
To maximize efficiency during portable offline pd tester assessments, the MOEORW‑Wi900PD features an AI Automatic Partial Discharge Defect Identification engine. Instead of relying on manual pattern interpretation, the embedded intelligence automatically recognizes 5 critical defects on-site: floating potential, surface tracking, internal voids, corona from metal tips, and free-moving particle discharges.
Field-tested to deliver a 95% defect recognition accuracy, this capability reduces the diagnostic workload by 70%. By streamlining portable pd testing without complex setup, it empowers field operators with limited PD background to make confident, data-driven portable pd tester for acceptance decisions. This intelligent automation makes the device highly effective as a portable pd tester for transformer factory QA, smoothly guiding technicians through rigorous portable pd tester for transformer fat and sat procedures with minimized reliance on scarce expert resources.
Professional PRPD & PRPS Pattern Analysis
Generates PRPD (Phase‑Resolved Partial Discharge) and PRPS (Pulse Repetition Phase Spectrum) patterns. Supports real‑time display, local storage and historical data replay for fault trace‑back.
Help engineers evaluate partial discharge severity and insulation aging trend for predictive maintenance.
Non‑Intrusive Live‑Line Partial Discharge Testing
No power‑off required during field measurement, no direct contact with high‑voltage live components. Reduce power outage loss for end‑users and improve working efficiency for on‑site maintenance tasks.
Excellent Anti‑interference Performance for Substation Environment
Metal‑shielded host housing plus multi‑level sensor filtering algorithm, suppress substation electromagnetic noise, radio signals and mechanical vibration. Each sensor passes independent performance verification to ensure stable and reliable partial discharge detection under complex EMI conditions.
Dual‑screen & Wireless APP Synchronization
4.3‑inch touch LCD screen on main unit; supports mobile and tablet APP wireless sync. Operate detection, view PD patterns, generate inspection reports and export data via QR‑code directly onsite.
Field comparison tests show up to 50% improvement for whole inspection workflow.
Modular Optional Configuration
Optional modules: IR thermal imaging, SF6 gas leak detection, temperature & humidity measurement. Same main‑unit hardware platform for different configurations. Bulk resale clients can manage stock easily and select functions according to project budgets.
Rugged Hardware for Harsh Field Conditions
Sensor working temperature: ‑40℃ ~ +85℃; IP66‑IP68 protection grade. 5000mAh rechargeable battery, continuous working time ≥8 hours for outdoor substation patrol.

Application Scenarios
This partial discharge detector is widely applied for predictive maintenance of high‑voltage assets:
- Switchgear & Ring Main Unit partial discharge testing
- GIS Partial Discharge Detection
- Power & dry‑type transformer partial discharge test
- HV cable and overhead line PD inspection
Target Customers:
Power utility companies, substation maintenance teams, petrochemical plants, railway power supply system, third‑party testing laboratories, electrical equipment traders and system integrators for bulk resale.
Package List

▶ Main Unit MOEORW‑Wi900PD ×1
▶ Built‑in TEV & AA sensors
▶ External UHF, HFCT, AE sensors
▶ Focused flexible AA probe
▶ Type‑C charger & connection cables
▶ Protective hard carrying case
▶ English user manual
Purchasing Information
✔ Sample & Small Order: 1 unit is available for sample / project‑use purchase, stock available for fast delivery.
✔ Bulk Order: Quantity discount for orders ≥5 sets.
✔ OEM / ODM Service: Custom laser logo, multi‑language UI, customized test report template, configurable sensor combinations for resale partners.
✔ Production Lead‑time: Fast shipment for sample stock; fixed production cycle for large‑volume bulk orders.
✔ Quality Control: Every unit completes assembly, burn‑in aging test and multi‑point sensor calibration before shipment, individual calibration record can be provided.
✔ Certification: Complies with IEC 60270; ISO9001 & CE certified.
✔ Warranty: Standard 12‑month warranty; extended warranty solution for large project orders.
✔ Partner Support: Online technical training, remote troubleshooting and long‑term spare‑parts supply for bulk cooperation clients.
About Our Manufacturing Capacity
We are the original factory for partial discharge test equipment, not trading company.
- In‑house R&D team for hardware circuit, sensor matching and PD AI pattern‑recognition algorithm; independent firmware and APP software development.
- Standardized production workflow: incoming material inspection → assembly → burn‑in aging → multi‑point calibration → full‑function test before delivery, ensures consistent performance for bulk‑batch products.
- Stable monthly production capacity for partial discharge tester series; finished goods stock supports sample fast delivery.
- Mature OEM & ODM experience for worldwide electrical distributors and system integrators.

FAQ
Q: Can I buy only 1 unit for my project?
A: Yes, single‑unit sample order is supported.
Q: Do you support OEM custom logo for bulk resale?
A: Yes, we provide full OEM & ODM solutions for bulk partners.
Q: Does this partial discharge detector follow IEC 60270 standard?
A: Yes, the instrument complies with IEC 60270 partial discharge measurement requirements.
Q: Can it perform live‑line partial discharge test for GIS, transformer and switchgear?
A:Yes, non‑intrusive live‑line inspection is supported for above‑mentioned high‑voltage equipment.
Q: Will you supply calibration documents for each device?
A: Every unit passes factory calibration, calibration records are available upon request.
Q: What is the lead‑time for bulk orders?
A: Sample orders ship from stock; bulk order lead‑time depends on order quantity, please contact us for details.
Interested in MOEORW‑i900PD Multifunctional Partial Discharge Detector?
Contact us to get quotation, technical datasheet and bulk‑order discount.
Full Specifications
|
Technical Unit |
Technical indicators |
Technical parameters |
|
Infrared thermal imaging module |
Sensor type |
Uncooled detector |
|
Maximum image size |
512x384 |
|
|
Response band |
8-14μm |
|
|
NETD (Noise Equivalent Temperature Difference) |
<45mK |
|
|
thermal imaging lens focal length |
3.2mm F1.1 |
|
|
Lens type |
Wafer-level optics (WLO) |
|
|
Field of view |
56° |
|
|
Adjustment method |
Fixed focus |
|
|
Output frame rate |
25Hz |
|
|
Data Acquisition Module |
TEV ground wave, AA air-type ultrasonic detection module |
Working principle: capacitive voltage division, ultrasonic principle, built-in |
|
Sensor type: Square adsorption type |
||
|
Signal interfaces: BNC, SMA |
||
|
Measurement range: not less than 0 to 50 dBmV |
||
|
Operating frequency band TEV: 3MHz-100MHz , pulse counting error: ≤3%; Stability: The output value of the detector changes by no more than ±20% after power-on and continuous operation for 1 hour. AA: Air-coupled ultrasonic sensor, center frequency 200kHz |
||
|
Operating temperature: -40°C to +85°C |
||
|
HFCT high-frequency sensor |
Working principle: Rogowski coil |
|
|
Sensor type: Openable ring structure |
||
|
Operating frequency band: 1MHz-30MHz |
||
|
Sensor transmission impedance: ≥5mV/mA; |
||
|
Protection rating: IP68 |
||
|
Signal interface: N-50 socket or BNC connector optional |
||
|
Sensor inner diameter: 65mm or 45mm available |
||
|
Material: Alloy (meets 96-hour salt spray test requirements) |
||
|
Sensitivity: <5pC |
||
|
Detection error: ±1dB |
||
|
Resolution: ±0.1dB |
||
|
Dynamic range of detection: 70dB |
||
|
Operating temperature range: -40℃ to +85℃ |
||
|
AA Non- contact Sensor |
Center frequency: 40.0±1.0KHz , Detection sensitivity: ≤10pC |
|
|
Bandwidth (-6dB): 1.2 kHz ; Linearity error: no greater than ±20%. |
||
|
Transmitted sound pressure level: 120dB |
||
|
Receiver sensitivity: -63dB min |
||
|
Impedance: 900 |
||
|
Capacitance at 1kHz: 2400 picofarads ; Stability: Output value variation after power-on and 1 hour of continuous operation is no greater than ±20%. |
||
|
A E contact sensor |
Detection frequency band: not lower than 20kHz to 180kHz ; Detection sensitivity: ≤10pC; Linearity error: no greater than ±20%; Stability: The output value of the detector changes by no more than ±20% after power-on and continuous operation for 1 hour. |
|
|
UHF ( Ultra- High Frequency) Sensor |
Sensor frequency: 300MHz-1500MHz |
|
|
Casing: Metal |
||
|
Detection sensitivity: not less than 1 pC |
||
|
Antenna type: Butterfly |
||
|
Gain: +5dBi |
||
|
Matching impedance: 50Ω |
||
|
Sensor equivalent height: not less than 10 mm |
||
|
Operating temperature: -40℃ to +85℃ |
||
|
Protection rating: IP67 |
||
|
Wave gatherer |
Focused wave type AA flexible probe sensor |
Used for partial discharge detection of overhead lines |
|
earphone |
Headphone sound monitoring |
Equipped with anti-interference stereo headphones for real-time sound monitoring to help determine the level of discharge. |
|
barcode scanner module |
Support range |
One-dimensional barcode, two-dimensional barcode |
|
Reading accuracy |
One-dimensional barcode: code39 ≥ 4.9mil, QR code: QR ≥ 10mil |
|
|
Battery |
capacity |
5000mAh |
|
Charging port |
Type-C direct plug |
|
|
Voltage |
3.7v |
|
|
Data processing terminal |
Software System |
Supports Android |
|
Data Upload |
It supports uploading data to the cloud platform via 4G and 5G mobile networks. |
|
|
Communication function |
Supports GPS/AGPS/GLONASS/BeiDou/GALILEO/QZSS/NavIC/Bluetooth/WIFI |
|
|
Storage function |
It has 256GB of built-in memory and supports direct reading or export of data from USB flash drives. |
|
|
weight |
Less than 1000g |
|
|
runtime |
No less than 12 hours |
|
|
Instrument screen |
The device features an OLED display with a built-in color high-definition LCD screen, supporting dual-screen display, 1-120 Hz LTPO adaptive refresh rate, 1440 Hz high-frequency PWM dimming, and a 300 Hz touch sampling rate. It can also be operated via a tablet app. |
|
|
resolution |
FHD+ 2832 × 1280 pixels |
|
|
lens |
The all-in-one design is used to record on-site personnel operation procedures and equipment operation, and supports uploading to a cloud platform. It features a 50MP ultra-wide-angle camera, a 40MP ultra-wide-angle camera, and a 12MP periscope telephoto camera. |
|
|
zoom mode |
Supports 5.5x optical zoom with autofocus. |
|
|
Video recording |
It supports 4K (3840 x 2160) video recording to record the on-site inspection environment and equipment operation status, and supports uploading to the cloud platform. |
|
|
Protection level |
IP68 |
|
|
Power-on protection |
Supports 3D face recognition and fingerprint recognition. |
|
|
Thermal imaging detection function |
Supports switching between maximum and minimum temperatures and pseudo-color. Celsius and Fahrenheit temperature settings are also supported. Infrared images can be saved to the photo album and simultaneously to the detection record, allowing users to directly share the results. |
|
|
Data Management |
1. It can save various types of signal maps and dynamic data, including two-dimensional and three-dimensional images, and can query, export, and manage them; 2. Data can be transmitted to other devices via wired or wireless means. 3. Supports recording the current detection data and generating a detection report when abnormalities or alarms are detected . 4. The host can save ultra-high frequency, transient ground voltage, high frequency and ultrasonic detection data . 5. Supports sharing ; data can be uploaded to the cloud platform or viewed in the detection records. |
|
|
Detection function |
1. The instrument should possess anti-interference techniques such as frequency domain filtering, time domain filtering, noise separation, and shielding isolation to effectively filter out various complex interference signals. It should also have functions such as windowing, blanking, and scale adjustment to eliminate fixed-phase interference. 2. The instrument should have two-dimensional and three-dimensional detection windows such as trend graphs, PRPD, PRPS, correlation, flight window, trend window, and discharge analysis window. 3. The instrument has the function of recording single-cycle and continuous waveform data, and can repeatedly play back the real process of on-site detection, providing data support for secondary waveform analysis. 4. The instrument is equipped with a signal spectrum database, which stores typical data of partial discharge signals caused by metal particles, corona discharge, moving electrodes, and insulation defects, as well as typical data of various noise signals (such as radar and mobile phone signals). The measured signal can be compared and analyzed with the typical spectrum data stored in the database through the "imprint comparison" function to determine and identify the signal category. 5. The instrument has the function of positioning based on the amplitude comparison of the detection signal and the function of positioning based on the time difference between two detection signals. |
|
|
Signal synchronization |
It supports internal synchronization, external synchronization, and virtual synchronization; high-voltage power supplies can be directly connected to the synchronization interface for synchronization; the external synchronization unit and the host are synchronized via wireless communication. |
|
|
Specification |
Size and weight |
2 03 mm* 127 mm* 50 mm, 0. 9 KG |
Hot Tags: Portable PD Tester for Transformer Factory and FAT/SAT | MOEORW, China Portable PD Tester for Transformer Factory and FAT/SAT | MOEORW manufacturers, factory, GIS Partial Discharge Tester, Partial Discharge Tester For High Voltage Switchgear, ultrasonic partial discharge tester, 4 Channel Portable Partial Discharge Tester, Cable Partial Discharge Tester, Transformer Partial Discharge Tester