1. What Is an Impulse Voltage Test?
An impulse voltage test applies a single, extremely short-duration high-voltage pulse to an item of power equipment to verify that its insulation can survive the overvoltages caused by lightning strikes and switching operations in a real grid.
Unlike a power-frequency withstand test, which holds a steady 50/60 Hz voltage for one minute, an impulse voltage test delivers a waveform measured in microseconds - typically a 1.2 µs front rising to peak and a 50 µs decay back to half value - across the insulation being evaluated.
It is one of the mandatory type tests for power transformers, bushings, surge arresters, instrument transformers, switchgear, GIS, cables and insulators before they are placed in service.
This guide explains the standard waveforms, the applicable standards, the test procedure, and how to read a captured impulse waveform.
2. Why the Test Is Necessary
Overhead transmission lines are struck by lightning thousands of times per day across any national grid. Each strike injects a travelling voltage wave that propagates along the line and arrives at transformers, bushings and switchgear as an extremely short overvoltage.
Switching operations - closing a circuit breaker, energising a long line, clearing a fault - generate slower but still severe overvoltages inside the substation.
Equipment that survives steady-state power-frequency voltage can still fail under these transient stresses. The impulse voltage test reproduces both kinds of event in the laboratory so that manufacturers and utilities can prove, on a sample basis, that the insulation will hold up over decades of service.
3. The Four Standard Impulse Waveforms
3.1 Lightning Impulse Full Wave - 1.2/50 µs
This is the reference waveform for lightning type tests.
Front time T₁ = 1.2 µs (permitted tolerance ±30%, i.e. 0.84–1.56 µs)
Time to half-value T₂ = 50 µs (permitted tolerance ±20%, i.e. 40–60 µs)
Peak amplitude tolerance: ±3%
The full wave tests the main insulation between windings, between winding and earth, and between phases.
3.2 Lightning Impulse Chopped Wave - 2–6 µs
A chopping gap fires artificially into the waveform and terminates it at 2–6 µs. The sudden collapse couples high-frequency components into the winding, stressing inter-turn and inter-section insulation that a full wave does not reach.
Chopping time: 2–6 µs
Standard deviation of chopping time: < ±0.2 µs
Required for power transformers and instrument transformers per IEC 60076-4.
3.3 Switching Impulse Wave - 250/2500 µs
Slower and longer, representing the overvoltage caused by circuit breaker operations on EHV/UHV systems.
Front time Tcr = 250 µs
Time to half-value T₂ = 2500 µs
Used primarily for air gaps, external insulation and EHV apparatus.
3.4 Steep-Front Wave
A very fast front - up to 1000–2500 kV/µs - used for surge arrester steep-current tests and turn-to-turn insulation studies on compact windings.
4. Applicable Standards
| Standard | Scope |
|---|---|
| IEC 60060-1/-2 | High-voltage test techniques - general definitions and test requirements / measurement systems |
| GB/T 16927.1/.2 | Chinese equivalent of IEC 60060 |
| GB 311.1 | Insulation coordination for high-voltage T&D equipment |
| DL/T 848.5 | General technical specifications for HV test devices - impulse voltage generators |
| IEC 60076-4 | Power transformers - impulse voltage level and tests |
| IEC 60137 | Bushings - impulse tests |
When a supplier quotes "IEC 60060 compliant", what they mean is that the generator, divider and recorder together meet the measurement uncertainty and waveform tolerance requirements of these standards.
5. The Test Procedure - Step by Step
Set up the test object. Mount the transformer, bushing or other apparatus, connect the high-voltage lead from the generator output terminal to the test point, and connect the weakly damped capacitive divider across the object.
Choose the waveform mode. For a lightning full wave, distribute front and tail resistors across the generator stages. For switching or oscillating modes, swap resistor sets or add the external inductor per the manual.
Set the charging voltage. The generator charges through constant-current charging to a value that produces the desired peak voltage (typically 20% below rated, because no-load efficiency is ~90%).
Run a calibration shot. Fire at low voltage, capture the waveform on the digital recorder, verify the front time and tail time against the standard, and adjust Rf / Rt if needed.
Apply the formal shots. Typically three "reduced voltage" shots at 50–75% of rated, followed by three "full voltage" shots at the rated BIL. For chopped-wave tests, a separate set of chopped shots follows.
Evaluate. The recorder captures each shot. The test passes if:
peak amplitude within ±3%
front and tail times within tolerance
no abnormal oscillation (>5% peak oscillation ratio)
no flashover or breakdown during the shot
A standard type-test report is generated automatically by the control software, with waveform traces and a pass/fail verdict.
6. How to Read a Captured Impulse Waveform
When you open the oscilloscope trace, check four things:
Peak value - does it hit the target BIL within ±3%?
Front time (T₁) - between 0.3 and 0.9 of the peak; measure the virtual origin. Should land around 1.2 µs.
Time to half-value (T₂) - from virtual origin to the point on the tail where the voltage has decayed to 50% of peak. Should land around 50 µs.
Oscillation on the front - jagged ringing above 5% of peak usually means insufficient damping; add a slightly larger front resistor.
A "clean" 1.2/50 µs wave rises smoothly, peaks once, and decays without secondary crossings.
7. Common Failure Modes and What They Mean
Flashover across the test object during the shot - the object failed its insulation; waveform collapses early.
Waveform too slow on the front - front resistor too large, or load capacitance higher than expected.
Wavefront ringing - under-damped; increase front resistance or check divider ground connection.
Peak too low despite correct charging voltage - check that all stages fired; a misfired stage costs its full voltage (e.g. one stage out of four means you lost 100 kV).
Noisy trace - poor grounding, earth-loop between console and tower, or divider cable routed near high-voltage leads.
8. What You Need to Run the Test
A complete impulse voltage test system includes:
Impulse voltage generator (Marx circuit, sized to the BIL of your test objects)
DC charging unit with constant-current charging and auto-grounding
Weakly damped capacitive divider (±1% ratio accuracy, ≤100 ns response)
Digital recorder / oscilloscope (12-bit or better)
PLC control console with overvoltage / overcurrent / travel-limit protection
Chopping device (if transformer testing is in scope)
For distribution-class testing of transformers, bushings, arresters, switchgear and cables up to 35 kV class, a 400 kV / 30 kV 4-stage Marx generator is the standard starting configuration.
For 220 kV-class and above, scale up to the 1200 kV / 120 kJ type-test configuration.
9. Impulse Voltage Test vs Impulse Current Test
Worth a quick clarification: an impulse voltage test (1.2/50 µs) stresses insulation. An impulse current test (8/20 µs) - run on a separate impulse current generator - measures the residual voltage and charge-transfer capability of surge arresters. Arrester type tests require both.
10. Conclusion
The impulse voltage test is the single most decisive proof that a piece of high-voltage equipment will survive its working life. Master the four waveforms (1.2/50 µs full, 2–6 µs chopped, 250/2500 µs switching, steep-front), the IEC 60060 tolerances, and the waveform-reading checklist above, and you can specify, perform and interpret these tests with confidence.
Running an impulse voltage test program? Tell us your test objects and system voltage class - we will recommend the right generator, divider and recorder configuration.
